Welcome to the official website of Dongguan Shenpeng Electronics Co., Ltd!

Location:

HomeCenterNews

What is the development trend of the circulating water pump in the plumbing mattress?

Sources:Dongguan Shenpeng Electronics Co., Ltd  Release date: 2021-07-30  Browsing:

circulating water pump


Plumbing mattresses are also called plumbing blankets, plumbing electric blankets, constant temperature plumbing blankets, temperature-controlled plumbing mattresses, etc. It consists of two parts: plumbing mattresses and water storage. Its working principle is: the water is heated or cooled by the heating or cooling system in the water reservoir, and then the water is sent to the water heating mattress or the water heating kang by the circulating water pump to heat or cool the human body. For water heating mattresses or water heating Kang media, the water temperature heating range is generally specified to be within 70 degrees, and some special customers require the water temperature to be 100 degrees.


The above water temperature requirements actually have a lot to do with the material of the mattress. There are currently two types of mattresses on the market: PVC and silicone tubes.


PVC is actually a kind of vinyl polymer. Its material is an amorphous material. It has non-flammability, high strength, weather resistance and excellent geometric stability. The cost is relatively low. Many customers will reduce the cost. This material is selected, but the resistance of PVC is very large, so the pump often chooses a higher head when selecting, so as to meet the demand.


The silicone tube is made by adding raw silicone rubber to a double-roll mixer or a closed kneader, and gradually adding white carbon black and other additives to repeatedly refining uniformly. According to the technical standards of the industry, the product is made by extrusion. The cost of silicone tubing is relatively high, and manufacturers that target high-end customers will choose this material cushion, and the pump does not need to be too high in head.


The 220v AC water pump was the first to be used in the plumbing mattress industry, which not only poses a major safety hazard, but also generates particularly loud noises. It is becoming less and more unsuitable for the development of the industry. In addition, people’s requirements for health and sleep quality are getting higher and higher. Water pumps are gradually being eliminated by the industry. Therefore, in order to adapt to the development of the industry and people’s requirements for health and sleep quality, major manufacturers later developed DC micro-pumps with better performance in all aspects. Among them, Shenpeng Electronics was an earlier manufacturer of brushless DC pumps. Mainly engaged in the research and development, production and sales of brushless DC water pumps, it is a global brushless DC water pump solution expert.


The advantages of Shenpeng Electronic Brushless DC Water Pump are as follows:

1. Long life, no maintenance, small size, high efficiency, and low power consumption.

2. The stator and circuit board of the motor are potted with epoxy resin and completely isolated from the rotor, which solves the problem of water leakage caused by long-term diving of the motor-type DC water pump. It can be installed underwater and is completely waterproof.

3. Many parameters can be made with the same voltage. For example, a 24V water pump can have a head of 2 meters or a head of 7 meters. The water pump can operate at a wide voltage, for example, a 24V water pump can operate at a voltage below 24V.

4. The shaft of the water pump adopts a high-performance ceramic shaft, which has high precision and good wear resistance. Because the water pump adopts a precise fit between the shaft sleeve and the ceramic shaft, the noise is less than 25 decibels, and the lower power can even reach below 20 decibels, almost Achieve the mute effect.

5. The three-phase Hallless program-driven DC pump in the water pump can realize PWM speed regulation, analog signal input speed regulation, and potentiometer manual speed regulation, so that the flow rate and head can be adjusted.

6. The three-phase DC water pump has impeller rotor jam protection, reverse connection protection, overload protection, and overcurrent protection.

7. The three-phase program-driven DC water pump is controlled as a soft start, no impact, and low starting power consumption.

8. The three-phase program-driven DC circuit board can be completely separated from the pump body. There are no components in the pump body, and the pump body is made of high temperature resistant materials, so that the pump can be used in boiling water for a long time.

9. The three-phase DC program-controlled water pump has high technology content, high degree of intelligence, and convenient control.

10. The water pump can be configured with 4-division pipe thread or 6-division pipe thread according to customer needs to meet the needs of special customers.

11. Multifunctional design, can be used in diving or placed outside (installation position is lower than the liquid level)

12. The pump can be customized according to user requirements and designed according to customer requirements.


The future development trend of the plumbing mattress industry?

The future development trend of the plumbing mattress industry: it must be considered in terms of meeting the needs of industry development and meeting customer requirements. Therefore, no matter how the industry develops in the future, only by adapting to the development of the industry and satisfying the needs of customers can it truly benefit the invincible.


Return
Contact

Address: Dapu Industrial Zone, Gangzi Village, Changping Town, Dongguan City

Tel: +86-769-82550950

E-mail: sp005@dgshenpeng.com

Dongguan Shenpeng Electronics Co., Ltd Copyright © 2018 粤ICP备12044388号        FriendLink: mini pump  [SiteMap]